background image

Important Safety Information

1/16/20

3

These are common practices that may or may not be applicable to the products described in 

this manual.

Use Seat Belt and ROPS

Land Pride recommends the use 

of a CAB or roll-over-protective-

structures (ROPS) and seat belt 

in almost all power machines. 

Combination of a CAB or ROPS 

and seat belt will reduce the risk 

of serious injury or death if the 

power machine should be upset.

If ROPS is in the locked-up 

position, fasten seat belt snugly 

and securely to help protect 

against serious injury or death 

from falling and machine overturn.

Keep Riders Off 

Machinery

Never carry riders or use 

tractor 

to lift or transport individuals.

There is not a safe place for a 

person to ride.

Riders obstruct operator’s view 

and interfere with the control of 

the power machine. 

Riders can be struck by objects or 

thrown from the equipment.

Prepare for Emergencies

Be prepared if a fire starts.

Keep a first aid kit and fire 

extinguisher handy.

Keep emergency numbers for 

doctor, ambulance, hospital, and 

fire department near phone.

911

Use Safety 

Lights and Devices

Slow moving tractors, and 

self-propelled equipment can 

create a hazard when driven on 

public roads. They are difficult to 

see, especially at night. Use the 

Slow Moving Vehicle (SMV) sign 

when on public roads.

Flashing warning lights and turn 

signals are recommended 

whenever driving on public roads. 

Avoid High Pressure 

Fluids

Escaping fluid 

under pressure can 

penetrate the skin 

causing serious injury.

Relieve all residual pressure 

before disconnecting hydraulic 

lines or performing work on the 

hydraulic system.

Make sure all hydraulic fluid 

connections are properly 

tightened/torqued and all 

hydraulic hoses and lines are in 

good condition before applying 

pressure to the system.

Use a piece of paper or 

cardboard, NOT BODY PARTS, 

to check for suspected leaks.

Wear protective gloves and 

safety glasses or goggles when 

working with hydraulic systems.

DO NOT DELAY.

 If an accident 

occurs, see a doctor familiar with 

this type of injury immediately. 

Any fluid injected into the skin or 

eyes must be treated within a few 

hours or gangrene may result.

Wear Personal Protective 

Equipment (PPE)

Wear protective clothing and 

equipment appropriate for the job 

such as safety shoes, safety, 

glasses, hard hat, dust mask, 

and ear plugs.

Clothing should fit snug without 

fringes and pull strings to avoid 

entanglement with moving parts.

Prolonged exposure to loud noise 

can cause hearing impairment or 

hearing loss. Wear suitable 

hearing protection such as 

earmuffs or earplugs.

Operating a machine safely 

requires the operator’s full 

attention. Avoid wearing 

headphones while operating 

equipment.

Summary of Contents for HRS3025













































Reviews: