manualshive.com logo in svg

Lancom WLC-4006, Manual, Page: 135 / 148

Share
Download
Lancom WLC-4006 Manual Download Page 135

LANCOM WLC series

 Chapter 7: Connecting two networks

134

EN

All entries for the central device are made just once and are then
stored to the device properties.

7.4

Instructions for WEBconfig

In WEBconfig, VPN-based network connectivity cannot be set up in
the Wizard. The Expert Configuration has to be used instead. Refer to
the reference manual for information on this.

Carry out the configuration on both routers, one after the other.

햲

In the main menu, launch the Wizard 'Connect two local area networks'.
Follow the Wizard’s instructions and enter the necessary data.

햳

The Wizard will inform you when the required information is complete.
You can then close the Wizard with 

Next

.

햴

Once you have completed the set-up of both routers, you can start testing
the network connection. Try to communicate with a computer in the
remote LAN (e.g. with 

ping

). The LANCOM Router should automatically

connect to the remote site and make contact to the requested computer.

Summary of Contents for WLC-4006





















































































































































Reviews:

No comments