Lafayette Parasol Accu-Rise Installation Instructions Manual Download Page 60

Page: 60 / 83

Parasol Installation Instructions

BACK

Cellular Window Shades

SkyLite

™

with Auto-Lift

™

Operation Installation Instructions

Thank you for choosing Parasol Cellular Shades. With proper installation and care,

your new shades will provide many years of beauty and performance.

Mounting Surface

Fastener

Wood

Drywall, Plaster

Metal

#6 Hex Head

Provided

Wall Anchors

Not Provided

Sheet Metal

Not Provided

Tools Needed

Power Drill, 1/4” Driver and drill bits

Tape Measure

Flat blade Screwdriver

Phillips Screwdriver

Pencil

Level

ASSEMBLE THE SHADE

- Orient the top rail with the fabric-colored shade facing

up and the bottom rail with the control knob facing up.

Arrange the side rails with the “L” sticker on the left

and the “R” sticker on the right. Orient the side rails so

that the top corner brackets are at the top and the

botton corner brackets are at the bottom.

- Slide the moving rail end caps close to the top corner

brackets.

Top Rail

Bottom Rail

Inside Mount

Installation

Bracket

Side

Rail

(Left)

Moving

Rail

Sensor Eye

and

Manual Control

Button

Bottom

Corner

Bracket

Satellite Battery Pack

Battery Wand

(For Shades Narrower than 28

Battery Wand

Cover

Battery Power Cable

Battery Wands

Holder

Spacer

Blocks

Battery Wands

(For 28

" and Wider Shades)

DC Power

Supply (Optional)

Satellite

Eye (Optional)

Moving

Rail

End Cap

Top

Corner

Bracket

Tension

Cable

Bottom Tension

Plate and Screw

Outside Mount

Installation

Bracket

Tension Screw

and

Top Tension

Plate

Corner Cover

Side

Rail

(Right)

Tension Cable

Bracket

Motor

Assembly

Top Corner Bracket

Bottom Corner Bracket

Moving Rail End Cap - Left

Moving Rail End Cap - Right

Grey

White

“L”

“R”

Summary of Contents for Parasol Accu-Rise




















































































Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands

Lafayette Parasol Accu-Rise, Installation Instructions Manual

Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands