Lafayette Parasol Accu-Rise Installation Instructions Manual Download Page 58

Page: 58 / 83

Parasol Installation Instructions

BACK

INSTALL THE SHADE

Outside Mount

- Your order will include four installation brackets, two

for each side rail, as well as one 3/8” screw and two

1 1/2” screws per installation bracket.

Important:

You

may need another person to assist you with this

installation.
- Attach the Installation brackets to the shade. (A.)

> Attach the installation brackets to the shade through

pre-drilled holes on the side rails using the 3/4”

screws provided.
- Mount the shade. (B.)

> Place the shade over the window opening at the

desired location, mark the screw holes and drill them

using a 3/32” drill bit.

Important:

Use drywall anchors

when mounting into drywall.

> Attach the installation brackets to the mounting

surface using the 1 1/2” screws provided.

REMOVE THE SHADE (If Necessary)

Inside Mount (C.)

- Raise the shade to the top. If there are screws

attaching the side rails to the window frame, unscrew

them.
- Insert a screwdriver at the lower corners of the shade

and push back the brackets to release the lower end

of the shade. Repeat to release the upper corners.

Outside Mount

- Unscrew the installation screws from the mounting

surface.

CARE AND CLEANING

Regular light dusting with a feather duster is all the

cleaning that is needed in most circumstances. For

deeper cleaning, vacuum gently with a soft brush

attachment. Do not vacuum Triple cell fabrics.

Installation

Bracket

Summary of Contents for Parasol Accu-Rise




















































































Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands

Lafayette Parasol Accu-Rise, Installation Instructions Manual

Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands