Lafayette Parasol Accu-Rise Installation Instructions Manual Download Page 33

Page: 33 / 83

Parasol Installation Instructions

BACK

Cellular Window Shades

Glissade Installation Instructions

Thank you for choosing Parasol Cellular Shades. With proper installation and care,

your new shades will provide many years of beauty and performance.

Mounting Surface

Fastener

Wood

Drywall, Plaster

Metal

#6 Hex Head

Provided

Wall Anchors

Not Provided

Sheet Metal

Not Provided

Tools Needed

Power Drill, 1/4” Driver and drill bits

Tape Measure

Flat blade Screwdriver

Phillips Screwdriver

Pencil

Level

Shade Width

12” - 31”

31 1/16” - 66”

66 1/16” - 96”

96 1/16” - 139”

139 1/16” - 168”

Brackets Required

INSTALL THE BRACKETS

Outside Mount

- Center the headrail over the window opening at the

desired height and lightly mark each end on a flat

    mounting surface.
  - Mark 8” from each end of the headrail.
  - Center the installation brackets or extension brackets

on your marks and mount flush against the mounting

surface using the screws provided. Use drywall anchors

if necessary.

Installation Bracket

Inside Mount Shim

Headrail

Stationary Rail

Bracket

Cord Tensioner

Cord

Tensioner

Stationary Rail

Bottom Bracket

Inside Mount

Adaptor

Moving Rail

Handle

Moving Rail

Bracket

Assembly

End Plate

Stationary

End Plate

Fabric Carrier

Bearing

Stationary

Rail

Snap Pin

End Plate Screw

Rail Carrier

Left Stack

Design

11/4" Valance

Clip

Valance

Corner

End Cap

Valance

Return

3/4

Valance

Clip

Lock

Floor Clearance

Top of

Bracket

Ordered

Shade

Height

5/8"

Outside Mount

Summary of Contents for Parasol Accu-Rise




















































































Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands

Lafayette Parasol Accu-Rise, Installation Instructions Manual

Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands