Lafayette Parasol Accu-Rise Installation Instructions Manual Download Page 15

Page: 15 / 83

Parasol Installation Instructions

PREPARE THE QUARTER CIRCLE SHADE

- The shade has two rails: one horizontal and one

vertical rail
- Fit the long side of the specialty end mount bracket into

    the small fabric channels on the horizontal rail.
  - Fan out the fabric.
  - Connect the two rails by sliding the vertical rail down

onto the short side of the specialty end mount bracket.

The bracket fits into the small fabric channels on the

vertical rail.

Long Side

of Bracket

Horizontal Rail

Small Fabric Channels

Long Side

( 3/8" Pleat Rail Similar)

3/4" Pleat Rail

Specialty End

Mount Bracket

Note: For 3/8" and

3/4" brackets only

11/4" Pleat Rail

Small Fabric Channels

INSTALL THE QUARTER CIRCLE SHADE

A. Standard

- Install both the horizontal rail and the vertical rail into

    the installation brackets.
  - Loosen the tab screw on each bracket.
  - Push the rails into the brackets. Make sure fabric is not

caught between the tabs and the rails.
- Tighten the tab screw on each bracket. Do not

overtighten. If necessary, gently move the fabric forward

to access the screw.

B. Swivel

- Install both the horizontal rail and the vertical rail into

    the installation brackets.
  - Position the moveable tab outward on each bracket.
  - With front side of the fabric facing you, lift the shade

into position so the rails are against the back of the

brackets..
- Rotate the moveable tabs against the rails to lock into

place. Make sure the shade is tightly secured.

Tab Screw

Front

Bracket Open

Bracket Locked

Locking

Tab

Screw Holes

Push

Tab

Locking Tab

Summary of Contents for Parasol Accu-Rise




















































































Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands

Lafayette Parasol Accu-Rise, Installation Instructions Manual

Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands