Lafayette Parasol Accu-Rise Installation Instructions Manual Download Page 37

Page: 37 / 83

Parasol Installation Instructions

BACK

INSTALL THE HEADRAIL

- Measure and mark the center point on the mounting

surface and the headrail’s center point.

Align the headrail by matching the marks.

- Slip the headrail into the installation brackets, with the

front of the bracket fitting under the groove of the

    headrail.
  - Push the headrail back and up until it snaps into place.
  - Inspect the installation brackets to verify the back of

the headrail is securely snapped into the base of each

bracket. Also the front edge of each bracket must be

in the groove of the headrail.

Note:

Once the headrail has been installed, it cannot

easily be adjusted by sliding it in the installation

brackets.

Headrail

Bracket

The front of the bracket

fits under the groove.

The back of the headrail

snaps into the bracket.

INSTALL STATIONARY RAIL BOTTOM BRACKET

Side/Split Stack and Duo-Lucent - Outside Mount

- To attach the stationary rail bracket(s) to the floor, use

a level to ensure that the stationary rail is exactly

vertical when viewed from both the front and side and

attach the bracket using the screw provided.

(A.)

-To attach the stationary rail bracket(s) to the wall, use

a level to ensure that the stationary rail is exactly

vertical and attach the bracket using the screw

provided.

(B.)

- You may use an extension bracket to mount the

stationary rail away from the wall. An extension bracket

may be necessary if you used spacer blocks or

extension brackets with the installation brackets.

Side/Split Stack and Duo-Lucent - Inside Mount

- To attach the stationary rail bracket to the floor, place a

screw through the bracket and into the floor.

-To attach the stationary rail bracket to the wall, use

the inside mount adaptor to secure the stationary rail to

the side of the jamb. Note: If you ordered your shade

with a cut-out, for baseboards or other obstructions,

you must use the inside mount adaptor.

(C.)

- Slide the inside mount adaptor onto the stationary rail

bottom bracket. Align the screw hole of the adaptor to

face the side jamb and secure with a screw through the

inside mount adaptor, into the side jamb.

(D.)

Stationary

Rail

Wall

(Left Stack

Illustrated)

Stationary Rail

Bottom Bracket

Stationary Rail

Bottom Bracket

Stationary

Rail

Extension

Bracket

(Side View)

Stationary

Rail

Bottom

Bracket

Stationary

Rail

Bottom

Bracket

Stationary Rail

Bottom Bracket

Adapter

Summary of Contents for Parasol Accu-Rise




















































































Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands

Lafayette Parasol Accu-Rise, Installation Instructions Manual

Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands