Lafayette Parasol Accu-Rise Installation Instructions Manual Download Page 2

Page: 2 / 83

Parasol Installation Instructions

BACK

Cellular Window Shades

Accu-Rise Installation Instructions

Thank you for choosing Parasol Cellular Shades. With proper installation and care,

your new shades will provide many years of beauty and performance.

Mounting Surface

Fastener

Wood

Drywall, Plaster

Metal

#6 Hex Head

Provided

Wall Anchors

Not Provided

Sheet Metal

Not Provided

Tools Needed

Power Drill, 1/4” Driver and drill bits

Tape Measure

Flat blade Screwdriver

Phillips Screwdriver

Pencil

Level

Middle

Rail

Bottom

Rail

Installation

Brackets

Handle

Headrail

INSTALL THE BRACKETS

Outside Mount

- Center the headrail over the window opening at the

desired height and lightly mark each end on a flat

    mounting surface.
  - Mark 2” from each end of the headrail.
  - Center the installation brackets or extension brackets

on your marks and

mount flush against the mounting

surface using the screws provided. Use drywall anchors

if necessary.

Inside Mount

- Measure 2” from each jamb for bracket location. If more

than two brackets came with your order, space

additional brackets evenly between the two and mark

their location.

- Mount brackets using the screws provided. Be sure the

front edges of the brackets are aligned and level to

each other. Shim the brackets if necessary.

Shade Width

12” - 36”

36 1/16” - 72”

72 1/16” - 108”

108 1/16” - 120”

Brackets Required

3/8” & 3/4”

Installation

Bracket

3/8” & 3/4”

End Mount

Brackets

1 1/4”

Installation

Bracket

1 1/4”

End Mount

Brackets

Inside Mount

Outside Mount

Summary of Contents for Parasol Accu-Rise




















































































Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands

Lafayette Parasol Accu-Rise, Installation Instructions Manual

Search results

Summary of Contents for Parasol Accu-Rise

Reviews:

Related manuals for Parasol Accu-Rise

Brands by name

Popular brands