Label Neptis SMP Installation Manual Download Page 47 | Manualshive

Page: 47 / 60

background image

22.2) MAGNETIC LOCK

Functions settings to activate magnetic lock:

Ÿ

F04 = ON

to activate electric lock output.

Ÿ

F05 = ON

to enable permanent driving, that keep magnetic lock powered with

closed door.

In the working program “Manual” the magnetic lock isn't powered with door closed,
so to move door manually.

Activating “Push & Go” function (P08 parameter), the magnetic lock isn't powered
with door closed in the automatics working program to allow manually opening. It
work only in the “Night lock” program.

23)

SAFETY SENSOR DEVICES

This section describes how to connect and configure properly some of the safety sensors in compliance with the standard EN12987
available on the market, to ensure a level of safety corresponding to PL = c, Category 2 as required by the standard EN16005.

23.1) SENSOR OA-EDGE T

WIRING CONNECTION SENSOR OA-EDGE T

WIRING CONNECTION

NEPTIS SMP OPERATOR

Wiring between the sensor and the terminal block of the PWN-T board on Neptis SMP operator

1. WHITE (+) Supply power

TERMINAL 17 (+)

2. BROWN (-) Supply power

TERMINAL 16 (-)

3. GREEN COM (Closing side)

TERMINAL 3 COM

4. YELLOW N.C. (Closing side)

TERMINAL 2 Safety sensor in closing

5. GREY N.O. (Closing side) do not connect

6. PINK COM (Opening side)

TERMINAL 7 COM

7. BLUE N.C. (Opening side)

TERMINAL 5 Safety sensor in opening

8. RED N.O. (Opening side) do not connect

9. BLACK (+) Test input

TERMINAL 25 TEST (+)

10. VIOLET (-) Test input

TERMINAL 26 GND (-)

DIP SWITCH SETTING ON OA-EDGE T PARAMETERS ON DIGITAL PROGRAMMER N-DSEL

A7 = ON

Low level test input.

F20 (S07) = ON

For safety sensor in closing

A8 = OFF

Input test delay 10msec..

F21 (S08) = ON

For safety sensor in opening

For other option and settings available on

F22 (S09) = OFF

Test level LOW

the safety sensor, see the instructions supplied
with the sensor OA-EDGE-T.

SETTING ON THE L-NEP BOARD

Jumper J13 =

position

P

47

«
...
45
46
47
48
49
...
»

Summary of Contents for Neptis SMP





























































Reviews:

No comments

Related manuals for Neptis SMP

Metalmaster 200d Pro DC GTAW

Brand: Tokentools Pages: 33

Brand: Car-O-Liner Pages: 92

Brand: Lampert Pages: 24

Mojave Sun IR MS-1500WOIRPH

Brand: Fire Sense Pages: 10

Brand: Parkside Pages: 113

Brand: LOTOS Pages: 20

Muto Premium XL120

Brand: Dormakaba Pages: 24

Brand: Saf-Fro Pages: 94

Brand: Jasic Pages: 16

Brand: Jasic Pages: 17

Brand: Jasic Pages: 19

Brand: CAME Pages: 32

Brand: ATE Pages: 9

Brand: Lincoln Electric Pages: 12

RED-D-ARC ES 275I

Brand: Lincoln Electric Pages: 32

RANGER 8 + DIESEL

Brand: Lincoln Electric Pages: 40

WELD-PAK 3200HD

Brand: Lincoln Pages: 48

Brand: TOOLCRAFT Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands