KYMCO AK 550 Service Manual Download Page 297

Page: 297 / 461

9.Electrical Systems

AK 550

9-32

Luggage Box Light

Light (Lighting angle adjustable):

The lamp lights up when Seat Pad is lifted up, goes out when closed. (The

Cabinet Light is provided with light-sensing switch; in case the user forgets to

close the Seat Pad or the Pad fails to fully close up, system will cut the power

automatically after a set time, preventing any power loss of battery.)

Remove 6 bolts, lift up the luggage box. See the external topic for the details.

Remove the luggage box switches connectors.

Remove the luggage box and switches.

Summary of Contents for AK 550














































































































































































































































































































































































































































































Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands

KYMCO AK 550, Service Manual

Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands