KYMCO AK 550 Service Manual Download Page 26

Page: 26 / 461

1.Quick Reference

AK 550

1-17

Troubleshooting

Vehicle can not be started

Preliminary 6 Step Inspection

1. Is the battery fully charged (12 V or higher). See the Battery topic for more

information.

2. Key-On and listen for any action with Fuel Pump / Fuel Pump Relay (It will turn

off automatically in 5-10 seconds)

3. Key-On to check for any failure lamp light up on dashboard. See

theSelf-Diagnosis topic for more information.

4. Is the Idle screw of Throttle Valve being changed or loose?

5. Has the vehicle under regular service? Is the gas station a good one?

6. Is the spark plug the correct model of specified by the vehicle builder? See

the Spark Plug topic for more information.

Summary of Contents for AK 550














































































































































































































































































































































































































































































Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands

KYMCO AK 550, Service Manual

Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands