KYMCO AK 550 Service Manual Download Page 233

Page: 233 / 461

6.Fuel System

AK 550

6-46

Plug in the tool to the ECU connector and turn on the ignition switch to send

power to the tool.

Place the scooter on its main stand and put the side stand up prior to using the

diagnostic tool.

�

The functions of the diagnostic tool include ECU version, model name, data

analysis and reset.

ECU version:

includes model name, ECU number, identifications

number and software version.

Failure codes:

DTC reading, DTC clearing, and troubleshooting.

Data analysis:

For ECU’s software inspection.

Reset:

For the setting function adjustment.

Summary of Contents for AK 550














































































































































































































































































































































































































































































Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands

KYMCO AK 550, Service Manual

Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands