KYMCO AK 550 Service Manual Download Page 209

Page: 209 / 461

6.Fuel System

AK 550

6-22

Set the engine stop switch to the “RUN” position.

Unplug the fuel pump connecter.

Set the multi meter to read battery voltage.

Touch the multi meter leads to the harness side of the fuel pump connector, with

the positive lead touching the red/black wire terminal and the negative lead

touching the green wire terminal.

Turn the ignition switch on. The battery voltage should show for a few seconds.

Replace the fuel pump if it is not functioning and the input voltage is correct.

If the battery voltage is not present check the following:

● Fuse

● Fuel cut-off relay

● ECU

Summary of Contents for AK 550














































































































































































































































































































































































































































































Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands

KYMCO AK 550, Service Manual

Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands