KYMCO AK 550 Service Manual Download Page 36

Page: 36 / 461

2.Periodic Maintenance

AK 550

2-5

Check CVT Transmission System Filter Wool

CVT Transmission System Filter Wool

Excessive dust accumulation in CVT Transmission System may result in

unsmooth engine operation; clean and replace Filter Wool regularly.

Clean Filter Wool regularly as specified in Maintenance Schedule; replace or

clean Filter Wool every 5000km

Replace Filter Wool

1. Remove side plate on the right.

2. Remove Fixing Bolts of Crankcase Right Cover.

3. Remove 2 Fixing Bolts of Filter Wool.

4. Replace Filter Wool.

Insert Method

Operate in reversed procedures as removal.

Cleaning Method

1. Remove side plate on the right.

2. Remove Fixing Bolts of Crankcase Right Cover.

3. Remove 2 Fixing Bolts of Filter Wool.

4. Clean Filter Wool body with air jet and clean out dirt from Crankcase Right

Cover.

Summary of Contents for AK 550














































































































































































































































































































































































































































































Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands

KYMCO AK 550, Service Manual

Search results

Summary of Contents for AK 550

Reviews:

Related manuals for AK 550

Brands by name

Popular brands