Kval Commander III Page 44 Operation Manual Download

Page: 44 / 168

About Revisions

2-14

KVAL Manual

About Revisions

Revisions are created after editing an existing

Door Job

Door Data

Feature Group

file in the

KvalCAM

library.

Revisions represent a save point in the history of editing, the

Principle

revision is the current save

point in the case of a

Door Data

Feature Group

In the case of a

Door Job

, the

Principle

is the loaded version into the editor.

Principle and Diff

Each Revision Panel contains a

Principle

and

Diff Button.

The

Diff Button

compares two files.

For information about using the

Diff Button

see “Using the Diff Button” on page 2-12.

Using the Principle Button

Normally the top file in the table is the principle. However, any revised file can be
assigned as the principle using the

Principle Button.

From the revision table, select to highlight the desired revision file.

Select the

Principle Button

The selected file will be highlighted in green and will be assigned as the principle

file.

Revisions at the Door Job Library

The

Door Job

file revisions be compared and any file can be assigned as the principle.

Summary of Contents for Commander III









































































































































































Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands

Kval Commander III, Operation Manual

Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands