Kval Commander III Page 102 Operation Manual Download

Page: 102 / 168

Machine Feedback and Machine Controls

3-21

Commander III Operation Manual

About the Lock Task Control Window

View the settings of the back section. Enable or disable lock processing routines.

The following feedback and actions are available:

Buttons

•

Locks Enable/Disable toggle button

: Select to toggle the

Lock section OFF or ON. In disable mode, all feedback will
stop, the background will turn gray and no cuts will be made.

•

Slow plate /Fast Plate toggle button

: Select to switch between

a slow lock or fast lock cutting process on the back section.

Table

•

X-Location:

The location of the cut on the X-Axis part of the door (feedback)

•

Face Bore:

Select to enable or disable the face bore. Feedback to button includes

depth of bore (Deep, Shallow)

•

Function Drill (Option):

Select to enable or disable the function drill.

•

Lock Backset:

Feed back only. the length of the backset on the lock

•

Edge Plate:

Select to enable or disable the edge plate routine

•

Edge Bore:

Select to enable or disable the edge bore.

Summary of Contents for Commander III









































































































































































Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands

Kval Commander III, Operation Manual

Search results

Summary of Contents for Commander III

Reviews:

Related manuals for Commander III

Brands by name

Popular brands