manualshive.com logo in svg

Kustom Signals Digital Eyewitness HD, Installation Manual

Share
Download
Kustom Signals Digital Eyewitness HD Installation Manual Download Page 51

 

 

Installation of GPS and Wi-Fi Antennas 

 

 

 

 

Manual Part Number: 

006-1219-00 Rev. 0 

5–3 

Digital Eyewitness

® 

HD 

In-Car Video System 

 

4.  Connect the 5.0 GHz antenna element to the trunk lid mount. Ensure the antenna is 

installed securely. The following figure shows a completed antenna installation.  

 

Figure 5-3.

  Completed Antenna Installation

 

Note:   The type and style of the antenna and its mount may differ from the figures 

shown.  

Note:   This completes the installation of the wireless equipment in the vehicle. This 

equipment has been tested at the factory but now must be configured by the 
wireless system installer for the department’s individual requirements. 

5.  Route the cable(s) to the rear of the DVR. 

 

Figure 5-4.

  Wireless Antenna Connections on Rear of DVR

 

 

 

 

 

 

Wireless File 
Transfer Antenna 
Connections 

Summary of Contents for Digital Eyewitness HD







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands