Kostal KSEM Operating Instructions Manual Download Page 72

Page: 72 / 98

Operation and operating the device

Solar portal

The connection to the solar portal can be activated
or deactivated in the “Configuration of KOSTAL Solar
Portal” menu. Information about the connection status is
also displayed.

The connection to the KOSTAL Solar Portal is only made
or broken after clicking on the “Save” button.

Parameter

Explanation

Last request

Time of last query to the solar portal.
A “-” means that there haven't been
any queries yet.

Last response

Time of portal’s last response.

Machine ID

An ID issued for the KOSTAL Smart
Energy Meter by the solar portal.

Serial number

Serial number of the KOSTAL Smart
Energy Meter

Article number

Article number of the KOSTAL Smart
Energy Meter.

Activate solar portal

Activate or deactivate connection/
transfer to the solar portal.

INFO

In the solar portal, the items and
serial numbers of the inverter must
be stated for logging in.

Summary of Contents for KSEM



































































































Search results

Summary of Contents for KSEM

Reviews:

Brands by name

Popular brands

Kostal KSEM, Operating Instructions Manual

Search results

Summary of Contents for KSEM

Reviews:

Brands by name

Popular brands