manualshive.com logo in svg

Kostal KSEM, Operating Instructions Manual

Share
Download
Kostal KSEM Operating Instructions Manual Download Page 57

57

4

© 2020 KOSTAL Solar Electric GmbH 

Operation and operating the device

4.2 Preparing  KOSTAL Smart Energy Meter

The  KOSTAL Smart Energy Meter has to be connected 
to an existing local network in order for you to access it.

This requires the following steps:

1. 

Install the  KOSTAL Smart Energy Meter in a distribu-
tor box on the top-hat rail according to the installation 
instructions provided and connect by cable.

2. 

Cover  KOSTAL Smart Energy Meter with the cover or 
protection against accidental contact of the sub-dis-
tribution in the distributor box.

3. 

Connect network cable to  KOSTAL Smart Energy 
Meter’s grid connection (LAN port).

4. 

Connect the other end of the network cable to a 
router/switch.

5. 

Reconnect sub-distribution to power supply. Wait for 
the  KOSTAL Smart Energy Meter’s launch process to 
end.

 

H

The  KOSTAL Smart Energy Meter is connected to the 
network.

2

3

4

5

1

Summary of Contents for KSEM



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands