Korg Pa3XLe, User Manual, Page: 403 / 472

399 Effects
Delay
Appe
ndix
b: Speed Switch
This parameter controls how the rotation speed (slow and fast) is
switched via the modulation source.
When
Mode
=
Toggle
, the speed will switch between slow and
fast each time you press the pedal or move the joystick. Via
MIDI, the speed will switch each time the modulation amount
exceeds 64.
When Mode = Moment , the speed is usually slow. It becomes
fast only when you press the pedal or move the joystick. Via
MIDI, modulation values above 64 set the speed to
Fast , and val-
ues below 64 set it to Slow .
c: Manual Speed Ctrl
If you wish to control the rotation speed manually, instead of
switching between Slow and Fast, select a modulation source in
the
Manual Speed Ctrl
parameter. If you don’t want to use man-
ual control, set this to Off .
d: Horn Acceleration
e: Rotor Acceleration
On a real rotary speaker, the rotation speed accelerates or decel-
erates gradually after you switch the speed. The
Horn and Rotor
Acceleration
parameters set the transition times between fast
and slow speeds.
g: Mic Distance
g: Mic Spread
This is a simulation of stereo microphone settings.
Delay
56: L/C/R Delay
This multitap delay outputs three Tap signals to the left, right,
and center respectively. You can also adjust the left and right
spread of the delay sound.
e: High Damp [%]
e: Low Damp [%]
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter
as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of 50, and the effect sound of both
channels is output from the center with a value of 0.
Mic Spread
Microphone Microphone
Mic Distance
Mic Distance
Rotary Speaker (Top View)
Rotary Speaker - Mic Placement
a
L Delay Time
[msec]
0...2730 Sets the delay time of TapL
Level 0...50 Sets the output level of TapL
b
C Delay Time
[msec]
0...2730 Sets the delay time of TapC
Level 0...50 Sets the output level of TapC
c
R Delay Time
[msec]
0...2730 Sets the delay time of TapR
Level 0...50 Sets the output level of TapR
d
Feedback
(C Delay)
–100...+100 Sets the feedback amount of TapC
Src Off...Tempo
Selects the modulation source of the
TapC feedback amount
Amt –100...+100
Sets the modulation amount of the
TapC feedback amount
e
High Damp [%] 0...100
Sets the damping amount in the
high range
Low Damp [%] 0...100
Sets the damping amount in the low
range
f
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
g Spread 0...50
Sets the width of the stereo image of
the effect sound
h
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 366
Amt –100...+100 Amount of modulation source
C Delay
R Delay
Left
Right
Feedback
Spread
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
Pa3XLe User Manual v100 (English).book Page 399 Thursday, May 29, 2014 5:42 PM