Kongskilde GXS 9005 Operator'S Manual Download Page 24 | Manualshive

Page: 24 / 70

background image

2. CONNECTION AND TEST DRIVING

PIGB-183X 04 GXS 9005 / P 0218

24

MOUNTING OF PTO DRIVE SHAFT

All GXS 9005 (P) machines are as standard  delivered with a PTO shaft with friction
clutch  and  free  wheel.  The  PTO  shaft  is  mounted  with  the  clutch  towards  the
machine side and the other end towards the tractor.

The guard of the PTO shaft is secured at both sides with the chain.

IMPORTANT:

For the warranty of the PTO shaft to be valid, and to retain the

durability, the following rules must be observed.



Always start the machine with the engine running at low speed.



Always start the machine with the PTO shaft in a position of

maximum 10

o

from horizontal.



Last, but not least:

Grease the PTO shaft and especially its profile

tubes every 40 working hours, minimum.



In order to ensure the function of the friction clutch, it must be aired

before the start of a new machine and after a long period of standstill.
See also the supplied instruction manual for the PTO shaft.

IMPORTANT:

Do not shorten your new PTO shaft until you are certain that it is

necessary. From the factory the PTO shaft is adjusted to the distance
from PTO to PIC which is standard on most tractor brands.

If it is still necessary to shorten the PTO shaft, please note the following:

«
...
22
23
24
25
26
...
»

Summary of Contents for GXS 9005







































































Reviews:

No comments

Related manuals for GXS 9005

Brand: Rain-Flo Irrigation Pages: 16

Brand: Hammer Strength Pages: 18

Brand: Jacto Pages: 12

Chicken Coop Plan 3x5

Brand: EASY COOPS Pages: 21

Chicken Coop Plan 4x6

Brand: EASY COOPS Pages: 18

Chicken Coop Plan 8x10

Brand: EASY COOPS Pages: 18

Brand: Garden Treasures Pages: 2

Brand: Yanmar Pages: 49

Brand: Fagor Pages: 12

Brand: Baltic Pages: 68

Brand: H&S Pages: 76

Brand: ICS Pages: 156

Brand: Warner Electric Pages: 14

Brand: Milestone Pages: 64

Brand: Flex-A-Seal Pages: 7

Brand: Topcon Pages: 38

Brand: GGM gastro Pages: 3

Brand: Wartmann Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands