Kongskilde GXS 9005 Operator'S Manual Download Page 9

Page: 9 / 70

1. INTRODUCTION

PIGB-183X 04 GXS 9005 / P 0218

11. Always adjust the speed to the conditions. If the machine has been marked with

a maximum speed limit, this should never be exceeded.

12. Do not stand near the machine while it is working.

13. When mounting the PTO drive shaft check that the number and direction of

RPM of the tractor matches those of the machine.

14. Always use hearing protectors if the noise from the machine is annoying or if

you are working with the machine for a considerable period in a tractor cabin,
which has not been silenced sufficiently.

15. Before raising or lowering the machine with the link arms of the tractor, check

that no persons are near the machine or touching it.

16. Do not stand near the guards of the cutting unit and do not lift the guards before

all revolving parts have stopped moving.

17. Never use the machine for other purposes than what it has been constructed

for.

18. Do not allow any children to be near when you are working with the machine.

19. Never stand between the tractor and the machine during connection and

disconnection.

Summary of Contents for GXS 9005







































































Search results

Summary of Contents for GXS 9005

Reviews:

Related manuals for GXS 9005

Brands by name

Popular brands

Kongskilde GXS 9005, Operator'S Manual

Search results

Summary of Contents for GXS 9005

Reviews:

Related manuals for GXS 9005

Brands by name

Popular brands