Komatsu WA800-3E0 Operation & Maintenance Manual Download Page 290

Page: 290 / 336

SERVICE PROCEDURE

MAINTENANCE

4-66

(7) Torque converter mount trunnion (1 place)

(8) Fan pulley bearing (1 place)

(9) Tension pulley bearing (2 places)

NOTICE
Do not use air pressure or oil pressure to carry out high-
pressure greasing.

TIGHTEN ROPS CANOPY

Loosen the bolt, then remove the cover.

Check that there is no looseness in mounting bolts (1) of
the ROPS canopy. If any bolt is loose, tighten it.

Tightening torque: 2452 to 3040 Nm (250 to 310 kgm)

Install the cover.

The tightening torque is large, so a power wrench is
needed when tightening. Please request your Komatsu dis-
tributor to carry out this work.

Summary of Contents for WA800-3E0
















































































































































































































































































































































Search results

Summary of Contents for WA800-3E0

Reviews:

Related manuals for WA800-3E0

Brands by name

Popular brands

Komatsu WA800-3E0, Operation & Maintenance Manual

Search results

Summary of Contents for WA800-3E0

Reviews:

Related manuals for WA800-3E0

Brands by name

Popular brands