background image

OPERATION

TROUBLESHOOTING

3-155

OTHER TROUBLE

3

ELECTRICAL SYSTEM

3

q

(    ): Always contact your Komatsu distributor when dealing with these items.

q

In cases of problems or causes which are not listed below, contact your Komatsu distributor for repairs.

Problem

Main causes

Remedy

Lamp does not glow brightly even 
when the engine runs at hight speed

•Defective wiring

•Defective adjustment of alternator 
best tension

(•Check, repair loose  terminals,  
disconnections)
 •Adjust alternator belt tension  
For details, see EVERY 250  
HOURS SERVICE

Lamp flickers while engine is running

Battery charge caution pilot lamp 
does not go out even when engine is 
running

•Defective alternator
•Defective wiring

(•Replace)
(•Check, repair)

Abnormal noise is generated from 
alternator

•Defective alternator

(•Replace)

Starting motor does not turn when 
starting switch is turned to ON

•Defective wiring
•Insufficient battery charge

(•Check, repair)
 •Charge

Pinion of starting motor keeps going 
in and out

•Insufficient battery charge

 •Charge

Starting motor turns engine slug-
gishly 

•Insufficient battery charge
•Defective starting motor

 •Charge
(•Replace)

Starting motor disengages before 
engine starts

•Defective wiring
•Insufficient battery charge

(•Check, repair)
 •Charge

Pre-heating monitor does not light

•Defective wiring
•Defective heater relay
•Defective monitor pilot lamp

(•Check, repair)
(•Replace)
(•Replace)

Engine oil pressure monitor lamp 
does not light up when engine is 
stopped (starting switch at ON posi-
tion)

•Defective wiring
•Defective wiring, defective sensor

(•Replace)
(•Check, repair, replace)

Battery charge caution pilot lamp 
does not light up when engine is 
stopped 
(starting switch at ON position)

•Defective wiring
•Defective monitor

(•Check, repair)
(•Replace)

Outside of electrical heater is not 
warm when touched by hand

•Defective wiring
•Disconnection in electrical heater
•Defective operation of heater relay 
switch

(•Check, repair)
(•Replace)
(•Replace heater switch)

Summary of Contents for WA800-3E0

















































































































































































































































































































































Reviews:

Related manuals for WA800-3E0