Komatsu WA800-3E0 Operation & Maintenance Manual Download Page 28

Page: 28 / 336

SAFETY LABELS

SAFETY

2-6

SAFETY LABELS

(1) Caution before starting (09651-A0481)

Warning!

Read manual before operation, maintenance, disassembly,
assembly and transportation.

(2) Caution for lock lever (09654-C0481)

Sign indicates a hazard of unexpected moving of stopped
machine.

Lower working device to the ground, move safety lever to
lock position and take engine key with you before leaving
machine.

(3) Caution when traveling in reverse

WARNING

To prevent SEVERE INJURY or DEATH, do the following
before moving machine or its attachments:

Honk horn to alert people nearby.

Be sure no one is on or near the machine.

Use spotter if view is obstructed.

Follow above even if the machine is equipped with back-
up alarm and mirrors.

Summary of Contents for WA800-3E0
















































































































































































































































































































































Search results

Summary of Contents for WA800-3E0

Reviews:

Related manuals for WA800-3E0

Brands by name

Popular brands

Komatsu WA800-3E0, Operation & Maintenance Manual

Search results

Summary of Contents for WA800-3E0

Reviews:

Related manuals for WA800-3E0

Brands by name

Popular brands