background image

TROUBLES AND ACTIONS

OPERATION

3-248

Engine

3

q

( ): Always contact your Komatsu distributor when dealing with these items.

q

In cases of problems or causes which are not listed below, contact your Komatsu distributor for repairs.

Problem

Main causes

Remedy

Engine oil pressure monitor lights 
up

•Engine oil level is low in oil pan (suck-
ing in air)

•Clogged oil filter cartridge

•Defective tightening of oil pipe, pipe 
joint, oil leakage from damaged point
•Disconnection, broken wiring to sen-
sor
•Defective sensor, defective monitor 

 •Add oil to specified level, see 
CHECK BEFORE STARTING
 •Replace cartridge, see 
EVERY 500 HOURS SERVICE
(•Check, repair)

(•Repair)

(•Replace)

Steam is emitted from top part of 
radiator (pressure valve)

•Cooling water level is low, leakage of 
water

•Dirt or scale accumulated in cooling 
system

•Defective engine water level sensor

•Defective engine water temperature 
gauge
•Abnormal rotation of the cooling fan 
on the radiator side
•Clogged radiator fin or damaged fin

•Defective thermostat
•Defective thermostat seal
•Defective water pump
•Loose radiator filler cap (high altitude 
operation)
•Disconnection, broken wiring to sen-
sor

 •Check, add coolant, see 
CHECK BEFORE STARTING
 •Clean or repair, see EVERY 
500 HOURS SERVICE
 •Change cooling water, clean 
inside of cooling system, see 
WHEN REQUIRED
(•Replace engine water level 
sensor)
(•Replace engine water temper-
ature gauge)
 •Ask for an inspection by the 
distributor
 •Clean or repair, see EVERY 
500 HOURS SERVICE
(•Replace thermostat)
(•Replace thermostat seal)
(•Check,replace,repair)
 •Tighten cap or replace packing
(•Repair, connect wiring)

Radiator water level monitor lights 
up

Engine water temperature gauge is 
in red range

Engine water temperature monitor 
lights up

Engine water temperature gauge 
display stays at lowest level and 
does not rise

•Defective water temperature gauge 
monitor
•Defective thermostat
•In cold weather, cold wind is blowing 
strongly against engine
•Abnormal rotation of the cooling fan 
on the radiator side

(•Replace water temperature 
gauge monitor)
(•Replace thermostat)
(•Install radiator curtain)

 •Ask for an inspection by the 
distributor

Engine does not start even when 
starting motor is turned

•Lack of fuel

•Air in fuel system

•No fuel in fuel filter

•Starting motor cranks engine slowly
•Fuel cut knob is pulled out
•Defective valve clearance, defective 
compression

 •Add fuel, see CHECK 
BEFORE STARTING
(•Repair place where air is 
sucked in)
 •Fill filter with fuel, see EVERY 
500 HOURS SERVICE
 •See ELECTRICAL SYSTEM
 •Push fuel cut knob back in
(•Adjust valve clearance)

Summary of Contents for PC2000-8 BACKHOE

























































































































































































































































































































































































































































































































Reviews: