Kiramek SCIBORG 825K Owner'S Manual Download Page 14

NOTE:  In the event the ignition switch triggers the 825K, the siren will blast 

for 30 seconds and then stop for 7 seconds.  If the ignition switch is still on, 
the siren will go off for another 30 seconds.  This cycle will repeat until the 
ignition switch is turned off.  For all other zones (trunk, hood, door, brake), 
the siren will sound for 30 seconds and the triggering zone will be bypassed. 
The bypassed zone will be re-enabled after it has been closed/secured, and the 
siren will then chirp once and the LCD pager will beep once. 

Secure Disarm.

    If  you  press  the    button  while  the  siren  is  going  off,  the 

siren will stop but the system will remain armed.  Press the    button again 

to disarm the system.

Whenever you are in an emergency situation where you need to alert others 

for help, simply press the    and 

  buttons at the same time.  The system 

will lock and arm, and the siren will go off and lights will flash for 50 seconds.

Pressing the    button any time during the 50 seconds will stop the siren.

Panic Mode

This feature protects your vehicle in the event a thief stops you while driving. 

To activate

, press and hold the    and 

  buttons for more than 2 seconds 

or press the Anti-Carjack Switch.  

When active, the LCD pager will display a flashing 

  icon, and the starter 

circuit  will  be  immobilized.    Thirty  seconds  later,  after  the  thief  has  driven 

a safe distance away from you, the siren will go off for 50 seconds while the 

Hazard/Parking lights flash.  Lights will continue to flash for 30 seconds after 

the siren stops, and then the siren will blast again. This cycle will repeat until 

Anti-Carjack Mode is deactivated.  Even if the thief stops to disable the siren, 

the engine will not start due to the immobilizer.

To deactivate

 Anti-Carjack Mode, press the    button and the system will 

disarm.

Anti-Carjack Mode

A passenger inside your vehicle can send an alert to your LCD pager 

by pressing the “CALL” button on the RF Antenna Unit.  

During a Page-out Call, the LCD pager will display the 

  icon and 

play a melody.

Page-out Call

SCIBORG 825K OWNER’S GUIDE

Summary of Contents for SCIBORG 825K

























Reviews: