manualshive.com logo in svg

Kipp & Zonen RaZON+, Instruction Manual

Share
Download
Kipp & Zonen RaZON+ Instruction Manual Download Page 61

61

IV_AIR_PRESSURE

IV_AIR_PRESSURE is the derived air pressure at the end of the averaging interval. This is the value being used by the internal sun 
tracking process and derived from the mean altitude. The mean altitude is a moving average over 30 seconds and only updated if 
deviating more than 50 m from the currently active altitude. When there is no GPS fix, the last known air pressure remains in effect. 
The following barometric formula is being used to convert from altitude to air pressure.

IV_AIR_PRESSURE = 1013 • e 

(-altitude / 7400)

• Pressure at sea level is 1013 mBar
• The scale height is 7400 m
• The altitude in m
• IV_AIR_PRESSURE in mbar

IV_IRR_DIFFUSE

IV_IRR_DIFFUSE is the mean diffuse irradiance in W/m2. Register IV_LEN indicates the length of the averaging interval. The sample 
rate is 1/s. Input PYRANO_DIFFUSE indicates whether samples in this register are being calculated or measured. When the samples 
are being calculated, the following formula is used.

I

diffuse

 = I

global

  - I

direct

•

 cos (ze)

Where:
• I

global

 is the calculated global irradiance in W/m2

• I

diffuse

 is the measured diffuse irradiance in W/m2

• I

direct

 is the measured direct irradiance in W/m2

• ze is the zenith angle in radians or degrees

IV_IRR_DIRECT

IV_IRR_DIRECT is the mean direct irradiance in W/m2. Register IV_LEN indicates the length of the averaging interval. The sample rate 
is 1/s.

IV_IRR_GLOBAL

IV_IRR_GLOBAL is the mean global irradiance in W/m2. Register IV_LEN indicates the length of the averaging interval. The sample 
rate is 1/s. Input PYRANO_DIFFUSE indicates whether samples in this register are being calculated or measured. When the samples 
are being calculated, the following formula is used.

I

global

 = 

I

diffuse

  + 

I

direct

 • cos ( ze )

Where:
• I

global

 is the calculated global irradiance in W/m2

• I

diffuse

 is the measured diffuse irradiance in W/m2

• I

direct

 is the measured direct irradiance in W/m2

• ze is the zenith angle in radians or degrees

IV_TEMP_PYRANO

IV_TEMP_PYRANO is the mean temperature in degrees Celsius of the radiometer measuring diffuse or global irradiance. Register 
IV_LEN indicates the length of the averaging interval. The sample rate is 1/s.

IV_TEMP_DIRECT

IV_TEMP_PYRANO is the mean temperature in degrees Celsius of the radiometer measuring direct irradiance. Register IV_LEN 
indicates the length of the averaging interval. The sample rate is 1/s.

Summary of Contents for RaZON+









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands