manualshive.com logo in svg

Kipp & Zonen RaZON+, Instruction Manual

Share
Download
Kipp & Zonen RaZON+ Instruction Manual Download Page 60

60

Measurement data and status block
The measurement data and status block holds information which is updated atomically at a predefined interval. Register IV_LEN 
indicates the length of the interval.

IV_DATE

IV_DATE holds the date at the end of the averaging interval. The date is stored as a 32-bit unsigned integer according the format 
‘YYYYMMDD’ using the formula:

IV_DATE = YYYY * 10000 + MM * 100 + DD

Where:
• YYYY is the 4-digit year
• MM is the 2-digit month
• DD is the 2-digit day of month

IV_TIME

IV_TIME holds the time at the end of the averaging interval. The time is stored as a 32-bit unsigned integer according the format 
‘HHMMSS’ using the formula:

IV_TIME = HH * 10000 + MM * 100 + SS

Where:
• HH is the 2-digit 24 hour based hour
• MM is the 2-digit minute
• SS is the 2-digit second

IV_SOLAR_AZIMUTH

IV_SOLAR_AZIMUTH is the solar azimuth angle in degrees at the end of the averaging interval. The value is calculated using a solar 
positioning algorithm, location, altitude, date and time and does not include any adjustments.

IV_SOLAR_ZENITH

IV_SOLAR_ZENITH is the solar zenith angle in degrees at the end of the averaging interval. The value is calculated using a solar 
positioning algorithm, latitude, longitude, altitude, date and time and does not include any adjustments.

IV_LATITUDE

IV_LATITUDE is the latitude in degrees north at the end of the averaging interval. This is the value being used by the internal sun 
tracking process. It is a moving average over 30 seconds and only updated if the distance to the currently active horizontal location 
is more than 100 m. When there is no GPS fix, the last known value remains in effect.

IV_LONGITUDE

IV_LONGITUDE is the longitude in degrees east at the end of the averaging interval. This is the value being used by the internal 
suntracking process. It is a moving average over 30 seconds and only updated if the distance to the currently active horizontal 
location is more than 100 m. When there is no GPS fix, the last known value remains in effect.

Summary of Contents for RaZON+









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands