manualshive.com logo in svg

KidKraft Cedar Summit BEAR CAVE LODGE FSC, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit BEAR CAVE LODGE FSC Installation And Operating Instructions Manual Download Page 83

 83 

1 x 

Back Ground 5/8 x 4-1/2 x 23-1/2”

Step 41:  Frame Assembly

Wood Parts

Hardware

6042

A:

 Make sure that lower frame assemblies are square then attach 1 (6021) Back Ground to the outside of the (6002) Long Posts 

using 4 (S11) #8 x 2” Screws (with FW1) making sure that it is flush to the bottom. (Fig. 41.3 & 41.4 )

B

: Making sure that it’s flush to the bottom of the (6020) Short Ground and (6018) Long Ground, attach 1 (6019) Rock Bottom to 

the Rock Rails using 4 (S20) #8 x 1-3/8” Wood Screws. Make sure that the notch is at the top, left hand side.(Fig. 41.1 )

C

: Place 1 (6042) Narrow Floor Board on the front end of the (6017) Floor Supports and 1 (6013) Floor Board on far end other as shown 

in (fig. 41.1) making sure they are flush with the (6002) Long Posts and (6026) Rock Rails. 

Do not attach these boards until Step 27.

D

: Using the (6042) Narrow Floor Board as a guide, place (0600) Bottom trim flush to the top of the front (6042) Narrow Floor 

Board and attach to the Rock Rails using 2 (S7) #12 x 2” Pan Screws (with FW1) and 2 (S20) #8 x 1-3/8” Wood Screws.

. 

(Fig. 41.1 )

 

E

: On the back side attach 1 (6034) Floor Back to the (6002) Long Posts using 1 (S7) #12 x 2” Pan Screw and 2 (H8) ¼ x 4-1/4” 

Hex Bolt (with lock washer, flat washer and t-nut) per side. (Fig. 41.2 & 41.3)

4 x 

#8 x 2” Screws 

S11

S20

S7

H8

6 x 

#8 x 1-3/8” Wood Screws 

4 x 

#12 x 2’ Pan Screw 

2 x 

1/4 x 4-1/4” Hex Bolt (LW1, FW1, TN1)

1 x 

Rock Bottom 5/8 x 5-1/4 x 23-1/2”

1 x 

Floor Board 5/8 x 4-1/4 x 21”

1 x 

Bottom Trim 5/8 x 4 x 23-1/2”

1 x 

Floor Back 15/16 x 5-1/2 x 23-1/2”

1 x 

Narrow Floor Back 5/8 x 3-14/16 x 21”

A

B

flush to 

bottom

6018

6020

6019

Fig. 41.1

flush

flush

6013

6042

0600

6017

6002

6026

S7

S20

S20

x 4

S20

A

B

x 4

flush to bottom

S11

Fig. 41.4

A

B

Fig. 41.3

6021

6026

6002

6034

A

B

S7

H8

Fig. 41.2

6034

6034

6021

6021

6021

6019

6013

0600

6034

S7

LW1

FW1

TN1

Summary of Contents for Cedar Summit BEAR CAVE LODGE FSC





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands