manualshive.com logo in svg

KidKraft Cedar Summit BEAR CAVE LODGE FSC, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit BEAR CAVE LODGE FSC Installation And Operating Instructions Manual Download Page 21

 21 

2677

Step 2: Frame Assembly 

Part 1

It is important to assemble the frame on a flat, smooth surface.

A:

  Place (2627) SW Wall Panel between 2 (2677) Narrow Panels noticing the panel orientations.  The tops and 

bottoms of the panels should be flush.   Make sure the panels are square then using the pilot holes as a guide 

pre-drill with a 3/16” drill bit and fasten the front (2677) Narrow Panel to (2627) SW Wall Panel and (2627) SW 

Wall Panel to the back (2677) Narrow Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags per side.  (fig. 2.1, 2.2 and 2.3)

2 x 

Narrow Panel 1-1/4 x 22 x 87”

1 x  

SW Wall Panel 1-1/4 x 42 x 87”

2677

2627

Fig. 2.2

Wood Parts

Fig. 2.1

2627

Flush

Hardware

8 x 

1/4 x 2-1/2” Wafer Lag

WL5

Flush

Notice front 

(2677) Narrow 

Panel overlaps 

(2627) SW Wall  

Panel

WL5

WL5

Notice (2627) SW Wall 

Panel overlaps back 

(2677) Narrow Panel

Front

Back

Swing Side

2677

Front

Flush

Top View

WL5

Fig. 2.3

x 4 per 

side

Notice grooves 

face inwards

Swing Side

2627

Notice counter sunk 

holes on the  outside 

Back

Flush

2677

Summary of Contents for Cedar Summit BEAR CAVE LODGE FSC





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands