manualshive.com logo in svg

KidKraft Cedar Summit BEAR CAVE LODGE FSC, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit BEAR CAVE LODGE FSC Installation And Operating Instructions Manual Download Page 136

 136 

Note:  When installing Pan Bolts make sure to look at holes so bolts go through the side with the round 

recess and the lock nuts go through the side with the hexagonal recess.  Keep all bolts loose until 

further step.

A:

  Attach the two remaining Elbow Assemblies as instructed in Steps 75 and 76.

B:

  Place TNR Brace Assembly against (6002) Long Post so it sits under the slide.  It is not attached yet.  (fig. 

78.1)

C: 

 On the fourth Elbow Assembly attached remove the pan bolt and nut which is facing the fort (installed in Step 

73).   (fig. 78.1)  

The bolt will no longer be needed, but keep the lock nut.

D: 

 

Loosely attach TNR3 Tube Support (at the slightly bent end) to the Clamp Ring using 1 (PB6) 

1/4 x  1” 

Pan 

Bolt (with FW1 flat washer and the previously removed LN1 lock nut).  (fig. 78.2)

E:

  Rotate TNR3 Tube Support and attach to (6002) Long Post using 1 (S6) 

#12 x 1” 

Pan Screw as shown in fig. 

78.2.

F: 

 Fully tighten screw and bolt.

Step 78:  Attach Elbow Assemblies and TNR3 Tube 

Support

Hardware

1 x 

#12 x 1” Pan Screw

1 x 

1/4 x 1” Pan Bolt 

 

(FW1 flat washer & LN1 lock nut - previously removed)

16 x 

1/4 x 3/4” Pan Bolt 

 

(LN1 lock nut)

PB6

Other Parts

1 x TNR3 Tube Support

4 x TNR2 Slide Clamp Ring

PB1

Attach 2 

remaining 

Elbow 

Assemblies

S6

Fig. 78.1

Fig. 78.2

Remove PB1 (1/4 x 3/4” 

Pan Bolt) first then install 

PB6 (1/4 x 1” Pan Bolt 

with flat washer)

6002

S6

PB6

Note:  Flat 

end down

TNR Brace Assembly

6002

TNR3 Tube 

Support

FW1

LN1

Summary of Contents for Cedar Summit BEAR CAVE LODGE FSC





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands