Keysight U1401B User'S And Service Manual Download Page 28

Page: 28 / 159

Getting Started

Keysight U1401B User’s and Service Guide

[c]

MODE

Selects output modes for constant voltage/

constant current, autoscan and autoramp.
Selects frequency (Hz), duty cycle (%), pulse width

(ms), and level adjustments for square wave

output.

Enters the adjustment mode (for autoscan and

autoramp outputs).

[c]

Selects a digit or the polarity to be adjusted.
The selected digit/polarity will be flashing on the

secondary display.

—

[c]

Adjusts a digit or the polarity.
Press to adjust the selected digit or toggle the

output polarity.

—

[c]

OUTPUT

Toggles the output state on and off.

indicates that the signal is being generated and

indicates that the output has been disabled.

—

[a] When the HOLD key is pressed for more then one second, its function depends on the present state of the instrument. If the instrument is

presently in the data hold mode, pressing this key for more than one second will exit the data hold mode; if the instrument is not in the data

hold mode, pressing this key for more than one second will enter or exit the dynamic recording mode.

[b] Only applicable when the instrument is in the dynamic recording mode.
[c] Shifted functions.

Table 1-4

Keypad functions (continued)

No.

Key

Function when pressed for less than one second Function when pressed for more than one second

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands