Keysight U1401B User'S And Service Manual Download Page 66

Page: 66 / 159

Making Measurements

Keysight U1401B User’s and Service Guide

Touch the surface to be measured with the thermocouple probe.

Read the display.

If you are working in a constantly varying environment, where the ambient

temperature is not constant, follow these steps:

Press

to select 0 °C compensation. This allows a quick measurement of

the relative temperature.

Avoid contact between the thermocouple probe and the surface to be measured.

After a constant reading is obtained, press

to set the reading as the

relative reference temperature.

Touch the surface to be measured with the thermocouple probe.

Read the display for the relative temperature.

Figure 3-4

Surface temperature measurement

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands