Keysight U1401B User'S And Service Manual Download Page 30

Page: 30 / 159

Getting Started

Keysight U1401B User’s and Service Guide

The display at a glance

To view the full display (with all segments illuminated), press

while turning

the rotary switch from OFF to any non-OFF position. After you are done viewing

the full display, press any key to resume the normal function, depending on the

rotary switch position.

The instrument will then enter power save mode if the auto power-off (

)

feature is enabled. To wake the instrument up, perform the following steps:

Turn the rotary switch (knob) to the OFF position;

Then turn the rotary switch to any position other than square wave output and

press any key.

Figure 1-6

Full display

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands