Keysight U1401B User'S And Service Manual Download Page 138

Page: 138 / 159

Maintenance

138

Keysight U1401B User’s and Service Guide

Replacement parts

This section contains information for ordering replacement parts for the U1401B.

Table 6-3

includes a brief description of each replacement part with its

corresponding part number.

To order replacement parts

To order replacement parts from Keysight:

Contact your nearest Keysight Sales Office or Service Center.

Identify the parts by their corresponding Keysight part numbers shown in the

replacement parts list.

Provide the instrument model number and serial number.

NOTE

You may find the latest U1401B parts list in the Keysight Test and Measurement

Parts Catalog (

http://www.keysight.com/find/parts

NOTE

Not all parts listed are available as field-replaceable parts.

Table 6-3

Replacement parts list

Part number

Description

U1401-46400

Battery cover (without screw)

U1401-60027

Battery assembly (rechargeable) 1.2 V NiMH 1300 mAh No.3

0515-5254

Battery cover screw tapping button-HD Phillips M3 x 0.5 8 mm

0950-5480

Power supply AC-DC switching 60 W 1-output (AC charger adapter)

2110-1463

Fuse 63 mA 250 V time-delay 20 x 5.2 x 5.2 mm

2110-1464

Fuse 0.63 A 250 V no time-delay 20 x 5.2 x 5.25 mm

U1401-38300

Bumper

U1401-44700

Stand

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands