Keysight U1401B User'S And Service Manual Download Page 133

Page: 133 / 159

Maintenance

Keysight U1401B User’s and Service Guide

133

Recharging the batteries

This instrument is powered by four sets of rechargeable batteries. Charge the

batteries immediately when the low battery annunciator starts flashing. It is

strongly recommended that you use only the specified type of 24 V AC adapter to

charge these rechargeable batteries. Do not turn the rotary switch while the

instrument is being recharged because a DC 24 V supply is applied to the

charging terminal.
Follow the procedures below to recharge the batteries:

Power down the instrument and disconnect all the test leads from the

terminals.

Plug the AC adapter into the jack on the side panel.

Set the slide switch at the

CHARGE

position.

The red light indicates that the batteries are being recharged.

When the batteries have been fully recharged, the green light turns on.

Remove the AC adapter and set the slide switch at the

M/S

position.

WARNING

Do not discharge a battery by shorting it or subjecting it to reverse polarity.
Do not mix different types of battery. Make sure a battery is rechargeable
before charging it.

NOTE

– A new rechargeable battery comes in a discharged condition and must be

charged before use. Upon initial use (or after a prolonged storage period), the

rechargeable battery may require three to four charge/discharge cycles

before achieving maximum capacity. To discharge, simply run the instrument

using the rechargeable battery's power until it shuts down or until the low

battery warning appears.

– In some instances, the instrument may indicate that the charging is complete

after ten minutes or so when charging a new rechargeable battery. This is a

normal phenomenon with rechargeable batteries. Remove the rechargeable

battery from the device, reinsert it, and repeat the charging procedure.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands