Keysight U1401B User'S And Service Manual Download Page 74

Page: 74 / 159

Making Measurements

Keysight U1401B User’s and Service Guide

Refresh hold (auto trigger)

The refresh hold mode freezes the displayed value until the reading variation

exceeds the specified number of counts.
This function will autotrigger and update the held value with a new measured

value. When a new value is updated, the instrument will beep once as a

notification. The keypad operation is similar to the operation of data hold mode.

Make sure the refresh hold mode is enabled in the setup mode.

Press

to enter the refresh hold mode.

– The present value will be held and the

annunciator will appear on the

display.

– It will be ready to hold the new measured value once the variation of the

instantaneous reading exceeds the preset variation count (defined in setup

mode); while it waits for a stable new reading, the

annunciator will

flash.

– The

annunciator will stop flashing once a stable new reading is

available, and then the new value will be updated to the display. The

instrument will beep once as a notification.

Press

to exit this mode.

For voltage and current measurements, the held value will not be updated if the

variation of the reading is below 500 counts. For resistance and diode

measurements, the held value will not be updated if the reading is

or open. For

all measurements, the held value will not be updated if the reading cannot reach a

stable state.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands