Keysight U1401B User'S And Service Manual Download Page 94 | Manualshive

Page: 94 / 159

background image

4

Changing the Default Settings

94

Keysight U1401B User’s and Service Guide

Setting the power saving mode

To enable auto power-off, set this timer to any value from 1 to 99 minutes.
This feature is incorporated for power saving. The instrument will automatically

turn off after the specified period of time, if none of the following happens within

that period:
– A key on the keypad is pressed
– A measurement function is changed
– The dynamic recording mode is activated
– The 1 ms peak hold mode is activated
– The auto power-off feature has been disabled in the setup mode

– The output has been enabled (the

annunciator is displayed)

To reactivate the instrument after auto power-off, turn the rotary switch to the

OFF position and then turn it on again.
If the instrument is to be used for a long period of time, you may want to disable

the auto power-off feature. When the auto power-off feature is disabled, the

annunciator will not be shown on the display. The instrument will remain

on until you manually turn the rotary switch to the OFF position, or until the

batteries run flat.

«
...
92
93
94
95
96
...
»

Summary of Contents for U1401B
































































































































































Reviews:

No comments

Related manuals for U1401B

Brand: ACECO Pages: 2

Brand: Eagle Eye Pages: 3

Brand: VALTRONICS Pages: 13

Brand: JIANGSU Pages: 8

Brand: Candela Pages: 4

Brand: Hach Pages: 38

Brand: Hach Pages: 28

Brand: Hach Pages: 40

POCKET COLORIMETER II

Brand: Hach Pages: 142

Brand: Hach Pages: 4

Brand: Hach Pages: 308

Brand: Hach Pages: 158

Brand: Hach Pages: 118

POCKET COLORIMETER II

Brand: Hach Pages: 116

Brand: Hach Pages: 132

Brand: Hach Pages: 8

Brand: Hach Pages: 38

Brand: Hach Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands