Keysight U1401B User'S And Service Manual Download Page 153

Page: 153 / 159

Performance Tests and Calibration

Keysight U1401B User’s and Service Guide

153

Output calibration

Set the slide switch to the

M/S

position.

Allow the instrument to warm up for 10 minutes before performing calibration.

To enter the calibration mode, press

and

for more than one

second. The primary display will indicate “CHEEP”.

Press

to enter the input calibration mode.

Turn the rotary switch to any one of the “Current Input/Voltage Output”

positions, and press

SHIFT

for more than one second to enter the output

calibration mode.

CAL-0 & CAL-1

In the output calibration mode, the primary and secondary display will show

“CAL-0” and “-rdy-” respectively.
Connect the output terminals to a multimeter (refer to

Table 7-1

on page 142 for

the recommended test equipment).

– CAL-0:

Press

OUTPUT

. The primary and secondary displays show “CAL-0” and

“00000” respectively.

Wait until the instrument reading becomes stable, then record the value.

– CAL-1:

Press

MODE

. The primary and secondary displays show “CAL-1” and “-rdy”

respectively.

Press

OUTPUT

. The primary and secondary displays show “CAL-1” and

“00000” respectively.

Press

to adjust the output voltage until the reading on the meter

is the same as the

CAL-0

value recorded above.

Press

MODE

to finish the

CAL-0

and

CAL-1

calibration.

After finishing the

CAL-0

and

CAL-1

calibration procedures, the instrument will

automatically enter the 1.5 V output calibration mode.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands