Keysight U1401B User'S And Service Manual Download Page 40

Page: 40 / 159

Getting Started

Keysight U1401B User’s and Service Guide

Remote Communication

The U1401B has a bidirectional (full duplex) communication capability that makes

it very easy to transfer data from the instrument to a PC.
The required accessory for this feature is an optional IR-USB cable, to be used

with an application software that is downloadable from the Keysight Web site.
To communicate with the personal computer through remote communication:

Set up the communication parameters of the instrument and the personal

computer you are using. The default values for baud rate, parity, data bits, and

stop bit for the instrument are 9600, n, 8, and 1 respectively.

Make sure that the USB driver and the Keysight data logger software has been

installed on your computer.

Attach the optic side of the cable to the communication port on the

instrument. Make sure that the text side is facing upwards. See

Figure 1-10

page 41.

Plug the other end of the USB cable terminal into the USB port of your

personal computer.

Use the data transfer software to retrieve the data that you need.

Press the flaps to remove the cable from the communication port of the

instrument. See

Figure 1-11

on page 42.

It is not recommended to remove the connector cover of the IR-USB cable. But

sometime, while pressing the flap to unplug the cable, the connector cover

may come off accidentally as shown in

Figure 1-11

on page 42. To reattach

the cover, simply slip the cover over the connector. Make sure that the text on

the cover is on the same side as the text on the top case of the connector. You

will hear a click when the cover snaps properly into its place.

NOTE

You will need to download the Keysight data logger software from Keysight’s

website in order to use this feature. Please go to:

http://www.keysight.com/find/

hhTechLib

to download the software.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands