Keysight U1401B User'S And Service Manual Download Page 51

Page: 51 / 159

Calibrator Output Operations

Keysight U1401B User’s and Service Guide

Defining the autoscan parameters in the memory

Press and hold

MODE

for more than one second to enter the autoscan adjustment

mode. A total of 16 steps with individually definable time interval and amplitude

are available.
When the instrument is in the autoscan adjustment mode, the secondary display

shows the amplitude. The first two digits of the primary display are used to

indicate which step is being adjusted. The last two digits of the primary display

are used to indicate time interval.

Press

MODE

to cycle through step, time interval, and amplitude adjustments.

The digit to be adjusted will flash on the display.

– For amplitude adjustment, press

and

to select the digit to be

adjusted, and then press

and

to adjust the value of the selected

digit. The amplitude can be set to any value within the selected output

range (±1.5 V or ±15 V for constant voltage output, ±25 mA for constant

current output).

– For time interval adjustment, press

and

to select the digit to be

adjusted, and then press

and

to adjust the value of the selected

digit. The time interval can be set within the range of 0 to 99 seconds.

– Press

for more than one second to directly reset the time interval and

amplitude of the present step to zero.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands