Keysight ixia BreakingPoint 20 Installation Manual Download Page 53 | Manualshive

Page: 53 / 66

background image

Software Specifications

The following table details the software specifications for BreakingPoint 20:

Software
Component

Specification

Browser
Client

Supported browsers: Adobe Flash (version 11.6.602.171) enabled browser (Internet
Explorer 10), Mozilla Firefox 18, Chrome, and Safari (Mac)

Not supported: Safari for Windows, and Safari 6.0.2 on Mac OS 10.8.2

Recommended minimum screen resolution: 1024 x 768

Minimum 2 Gb RAM

Telnet Client

Telnet client running VT100 emulation

Serial Client

Serial client running 115200/8/n/l/none

Light-Emitting Diodes

The light-emitting diodes (LEDs) status indicators are located on the front of BreakingPoint 20. See the
following table for descriptions of each LED and what each LED color represents:

LED

Color

Status

Description

Link LED

Green

Operational

Link is present.

Active
LED

Blue

Operational

Indicates that the link is ready to send and receive traffic.

Blinking
blue

Operational

Link is present and traffic is on the bus.

User LED

Multicolor

Operational

This LED indicates the user who has reserved the port.

Reserved
LED

Multicolor

Operational

This LED indicates the port group to which the user belongs.

Power
LED

Amber

Boot-up

Computer is booting up.

Green

Operational

Computer is powered on and operating.

Blinking
Green

Busy

Insufficient power supply, a blade is not properly seated, or
the computer is in update mode. Do not remove the hard drive
when the Power LED is blinking.

Appendix A Specifications

– 48 –

«
...
51
52
53
54
55
...
»

Summary of Contents for ixia BreakingPoint 20



































































Reviews:

No comments

Related manuals for ixia BreakingPoint 20

QSR-3920 Series

Brand: QTech Pages: 120

Brand: QSC Pages: 28

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

Brand: NETGEAR Pages: 14

Brand: U.S. Products Pages: 80

Brand: Moxa Technologies Pages: 51

Brand: Cameo Pages: 23

Brand: Xantech Pages: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Brand: Juniper Pages: 122

Brand: H3C Pages: 4

Brand: Variscite Pages: 17

Brand: EVGA Pages: 3

Brand: Westermo Pages: 28

Brand: NEC Pages: 114

Brand: Aztech Pages: 13

Brand: Xilinx Pages: 36

Brand: Enterasys Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands