Keysight ixia BreakingPoint 20 Installation Manual Download Page 40 | Manualshive

Page: 40 / 66

background image

Note:

The computer can be powered on when you connect the device under test to

BreakingPoint 20.

To connect a device under test to the chassis, do the following:

1. Locate a free data port on the chassis.

2. Connect one end of a supplied fiber-optic cable to the data port.

3. Connect the other end of the fiber-optic cable to a port on the device under test.

4. Repeat the preceding three steps for any additional optical data port connections.

Chapter 5 Installation Guide

– 35 –

«
...
38
39
40
41
42
...
»

Summary of Contents for ixia BreakingPoint 20



































































Reviews:

No comments

Related manuals for ixia BreakingPoint 20

Brand: dbx Pages: 8

Brand: National Instruments Pages: 5

Brand: National Instruments Pages: 76

Brand: National Instruments Pages: 34

SmartMedia Adapter PC Card REX-SMA01F

Brand: Ratoc Systems Pages: 75

Brand: Vivotek Pages: 136

Brand: Aleratec Pages: 12

Brand: Delta Pages: 2

Wireless Mini PCI Module

Brand: E-Tech Pages: 42

FRDM-STBC-SA9500

Brand: Freescale Semiconductor Pages: 2

Brand: Oracle Pages: 112

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

DG834GT - 108 Mbps Super G Wireless ADSL Router

Brand: NETGEAR Pages: 2

Brand: Cypress Semiconductor Pages: 16

Brand: National Instruments Pages: 130

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: Asante Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands