KEPCO BOP-MG, Operator'S Manual

Page: 14 / 194

iv
BOP-1K 031912
TABLE OF CONTENTS
SECTION PAGE
3.6.4.6 Message Unit Separator ............................................................................................................. 3-62
3.6.4.7 Root Specifier.............................................................................................................................. 3-62
3.6.4.8 Message Terminator ................................................................................................................... 3-62
3.6.5 Understanding The Command Structure .......................................................................................... 3-62
3.6.6 Program Message Syntax Summary ................................................................................................ 3-63
3.6.7 Status Reporting ............................................................................................................................... 3-63
3.6.7.1 Status Reporting Structure.......................................................................................................... 3-64
3.6.7.2 Operational Status Register ........................................................................................................ 3-66
3.6.7.3 QUEStionable Status Register.................................................................................................... 3-67
3.6.8 SCPI Program Examples .................................................................................................................. 3-67
SECTION 4 - CALIBRATION
4.1 General ................................................................................................................................................... 4-1
4.2 Test Equipment Requirements ............................................................................................................... 4-2
4.3 Calibration using Remote SCPI commands via GPIB or RS 232 Interface ............................................ 4-4
4.3.1 Calibration Procedure using SCPI Commands................................................................................. 4-5
4.4 Calibration Using Front Panel Keypad in Local Mode ............................................................................ 4-10
4.4.1 Understanding the Calibration Process ............................................................................................ 4-10
4.4.2 Calibration Procedure using Local Mode .......................................................................................... 4-12
4.5 Calibration Storage ................................................................................................................................. 4-15
APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-2
A.5 *ESR? — Event Status Register Query.................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query .................................................................................................... A-3
A.9 *OPT? — Options Query ........................................................................................................................ A-4
A.10 *RCL — Recall Command ...................................................................................................................... A-4
A.11 *RST — Reset Command....................................................................................................................... A-4
A.12 *SAV — Save Command........................................................................................................................ A-4
A.13 *SRE — Service Request Enable Command ......................................................................................... A-5
A.14 *SRE? — Service Request Enable Query .............................................................................................. A-5
A.15 *STB? — Status Byte Register Query .................................................................................................... A-5
A.16 *TRG — Trigger Command .................................................................................................................... A-5
A.17 *TST? — Self Test Query ....................................................................................................................... A-6
A.18 *WAI — Wait-To-Continue Command .................................................................................................... A-6
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ............................................................................................................................................. B-1
B.2 Numerical Values.................................................................................................................................... B-2
B.3 ABOR
t
Command................................................................................................................................... B-2
B.4 CAL Commands and Queries................................................................................................................. B-2
B.5 INIT
iate
[:IMM
ediate
] Command ............................................................................................................ B-3
B.6 INIT
iate
:CONT
inuous
Command .......................................................................................................... B-4
B.7 INIT
iate
:CONT
inuous
Query ................................................................................................................. B-4
B.8 MEAS
ure
[:SCAL
ar
]:CURR
ent
[:DC]? Query.......................................................................................... B-4
B.9 MEAS
ure
[:SCAL
ar
]:MODE[:DC] Command .......................................................................................... B-4
B.10 MEAS
ure
[:SCAL
ar
]:VOLT
age
[:DC]? Query .......................................................................................... B-4
B.11 MEAS
ure
[:SCAL
ar
]:TRAN
sient
[:DC]? QUERY..................................................................................... B-4
B.12 MEM
ory
:UPD
ate
Command .................................................................................................................. B-5