KEPCO BOP 5-20DL, Operator'S Manual

Page: 5 / 70

LIST OF FIGURES
FIGURE TITLE PAGE
BOP 5-20DL 081915
iii
1-2 BOP Output Characteristic.......................................................................................................................... 1-6
1-3 BOP Output WaveForm with Phase Shift ................................................................................................... 1-7
1-4 Boundaries and Limits ................................................................................................................................ 1-11
1-5 Mechanical Outline Drawing, BOP 5-20DL ................................................................................................. 2-15
2-1 BOP 5-20DL, Terminations and Controls, Front Panel ............................................................................... 2-1
2-2 BOP Terminations and Controls, Rear Panel ............................................................................................. 2-3
2-3 A-C Source Voltage Selection .................................................................................................................... 2-3
2-4 Slide Installation on Full-rack Units ............................................................................................................. 2-7
2-5 Load Connection Using Local Sensing at Rear Panel ................................................................................ 2-9
2-6 Load Connection Using Local Sensing at Front Panel ............................................................................... 2-9
2-7 Load Connection Using Remote Sensing at Rear Panel ............................................................................ 2-10
2-8 Load Connection Using Remote Sensing at Front Panel ........................................................................... 2-10
3-1 Rear Programming Connector Terminals ................................................................................................... 3-2
3-2 BOP Voltage Control Channel (Local Control, Local Sensing) ................................................................... 3-4
3-3 BOP (±) Current Limiting Circuit (Local Control, Local Sensing) ................................................................ 3-6
3-4 BOP Current Control Channel (Local Control, Local Sensing) ................................................................... 3-7
3-5 BOP (±) Voltage Limiting Circuit (Local Control, Local Sensing) ................................................................ 3-8
3-6 Remote Potentiometer Control of D-C Output Voltage ............................................................................... 3-9
3-7 Remote D-C Output Voltage Control Using Two-Terminal Resistance (Decade)....................................... 3-10
3-8 Digital Control of the D-C Output Voltage ................................................................................................... 3-11
3-9 D-C Output Voltage Control with Non-inverting Configuration and High Impedance ±1V Signal Source ... 3-12
3-10 Graphs Of Possible Input/output Waveshapes ........................................................................................... 3-13
3-11 Basic Programming Circuit for Use of BOP as Bipolar Amplifier (Voltage Mode)....................................... 3-13
3-12 Programming Circuit for Driving Output Voltage with.................................................................................. 3-14
3-13 Symmetrical Remote Control of the Current Limits..................................................................................... 3-15
3-14 Independent Remote Control of + I
O
and – I
O
Limits.................................................................................. 3-15
3-15 Remote Potentiometer Control of the BOP Output Current ........................................................................ 3-16
3-16 Remote D-C Output Current Control Using Two-Terminal Resistance (Decade) ....................................... 3-16
3-17 Digital Control of Output Current................................................................................................................. 3-17
3-18 BOP Output Current Control with Non-inverting Configuration
and High Impedance (±)1 Volt Signal Source ......................................................................................... 3-17
3-19 Basic Programming Circuit for BOP as Bipolar Current-stabilized Amplifier............................................... 3-18
3-20 Programming Circuit for Driving Output Current with Bipolar Signal Less Than ±10V ............................... 3-18
3-21 Programming Circuit for Driving Output Current with a High Impedance Source ....................................... 3-19
3-22 Symmetrical Remote Control of Voltage Limit ............................................................................................ 3-19
3-23 Independent Remote Control of +E
O
and –E
O
Voltage Limit...................................................................... 3-20
3-24 Series Connection (Master/Slave) of two BOP Power Supplies,
with Remote Error Sensing at the Common Load................................................................................... 3-21
3-25 Circuit Breaker Control Circuit, Simplified Diagram. ................................................................................... 3-23
3-26 Parallel Connection (Master/Slave) of Two BOP Power Supplies
with Remote Error Sensing at the Common Load................................................................................... 3-25
3-27 Alternative Parallel Connection (Master/Slave) for
Greater Precision and Stability of Two or More BOP Power Supplies ..................................................... 3-26
3-28 Indicator Light and Flag Logic ..................................................................................................................... 3-27
3-29 Simplified Schematic Diagram, BOP 5-20DL.............................................................................................. 3-29
4-1
Location of Internal Calibration Controls ..................................................................................................... 4-2
4-2 Cover Removal and Internal Component Locations, BOP 5-20DL ............................................................. 4-6