background image

KDS-7XII Radio Remote Control System   

-1-

 

Introduction 

Thank  you  for  purchasing  KDS-7XII  Radio  Remote  Control  System  (hereafter  called  K-7XII). 

This system is extremely versatile and may be used by beginners and

 

professionals

 

alike. In order 

for you to make the best use of your system and to fly safely, please read this manual carefully. If 

you have any difficulties while using your system, please contact your hobby dealer. 

Liability Declaration 

 

KDS  model  has  the  right  to  change  the  product,  including  the  exterior,  the  functions 

parameter, and use request, but no notice. 

 

KDS  model  does not  provide any  guarantee,  declaration  and  promise  for  special  use  of  any 

KDS products. 

 

The  recommended  or  text  technologies  data  in  the  technology  introduction  for  KDS  model 

only indicates the test result at that time, but it does not mean KDS model acknowledges the 

result in law. 

 

KDS  model  will  not  be  responsible  for  the  result  made  by  using  any  product  or  circuit, 

including the incidental or indirect compensation. 

 

The parameters of KDS electronic products will be changed under different conditions. The 

products will work only after all the functions parameters are approved by each use intension. 

Precaution of Safety 

 

It  requires  professional  skills  and  technical  knowledge  to  install  and  operate  R/C  model 

properly.  Incorrect installation and operation will result in severe property loss and personal 

injuries. 

 

KDS-7XII  2.4GHz  is exclusively  designed for civil  use  of  R/C  models. Don’t  use it in any 

other flying machines. 

 

The governmence for R/C model is different in different place, therefore, please consult your 

local regulatory body and follow the rules and regulations to operate legally. 

 

Radio wave transfers almost in straight routine in 2.4GHz, please make sure there is no any 

obstacle when you are operating the product. The antenna tube should point at the controlled 

model  to  ensure  efficient  control,  and  keep  conductive  materials  away  from  receiver  and 

transmitter. 

 

If  there  is  prang,  collision,  welter  and  other  accidents  when  operating,  please  test  all  the 

things before next operating. 

 

Always keep electronic components away from small children. 

 

Stop flying long before your batteries become low on charge. Do not rely on your radio's low 

battery warning systems, intended only as a precaution, to tell you when to recharge. Always 

check your transmitter and receiver batteries prior to each flight. 

 

While you are getting ready to fly, if you place your transmitter on the ground, be sure that 

Summary of Contents for KDS-7XII

























Reviews: