English
23
Store the device in a dry and well-ventilated interior
space.
Do not expose the device to direct sunlight for a long
time.
Keep the device away from corrosive substances such
as garden chemicals and de-icing salts.
5. Store the device in a dry, well ventilated interior
space.
Care and maintenance
DANGER
Risk of injury due to cuts from sharp blades and ac-
cidentally switching on the device!
Remove the battery from the device before all work on
the device.
Make sure that the ON/OFF button is not pressed while
inserting the battery pack.
Avoid unintentionally switching on the device.
Wear safety goggles and protective gloves when work-
ing on the device.
Always mount the blade guard before working on the
device and before transporting it.
Cleaning the device
ATTENTION
Risk of damage due to incorrect cleaning!
Only clean the device with a hand-held brush and damp
cloth.
Do not use solvent-based cleaning agents.
Do not immerse the device in water or other liquids.
Do not clean the device with a hose or high-pressure
water jet.
1. Release the ON/OFF button.
The device switches off.
2. Remove the battery pack from the device, see chap-
ter
3. Remove cuttings with a hand-held brush.
Illustration T
4. Remove resin from the blades, e.g. with the Kärcher
Universal Stain Remover RM 769.
5. Oil the blades of the grass or shrub shears, see
chapter
.
6. Mount the blade guard, see chapter
7. Clean the device with a damp cloth if required.
8. Remove dirt and foreign objects from the battery
pack holder with a damp cloth.
Note
Clean the optionally available telescoping handle in the
same way.
Oiling the blades
Note
To maintain blade quality and optimum cutting results,
apply a little spray oil or thin machine oil to the blades of
the grass and shrub shears after each use.
1. Release the ON/OFF button.
The device switches off.
2. Remove the battery pack from the device, see chap-
ter
.
3. Clean the device, see chapter
4. Place the device on a horizontal, level and oil-resist-
ant surface.
Illustration U
5. Apply a thin layer of oil to the top of the blades of the
grass and shrub shears.
6. Mount the blade guard, see chapter
7. Clean the base and dispose of oil residues in an en-
vironmentally friendly manner and in accordance
with local regulations.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Error codes and error descriptions
Fault
Cause
Rectification
The device is not work-
ing.
The battery pack is not sitting properly in
the device.
1. Push the battery pack into the battery
mount on the device until it you feel it latch
into place.
The charging state of the battery pack is
too low.
1. Charge the battery pack, see chapter
The battery pack is overheated.
1. Take the battery pack out of the device and
let it cool down, see chapter
.
Note
The battery pack can get very warm.
2. Do not the place the device and battery
pack in direct sunlight.
The battery pack or charger is defective. 1. Replace the battery pack or charger, see
The device stops during
operation
Motor has overheated
1. Stop working and allow the motor to cool
down.
Charge indicator
Error description
Error correction
An LED flashes slowly
and the motor is off.
The battery pack is fully discharged. 1 Charge the battery pack or replace it with a charged
battery pack, see chapter
.
Summary of Contents for GSH 4-4 Plus
