KAESER EPC 1500-G Assembly And Operating Manual Download Page 62

Page: 62 / 102

8. Attach the sound enclosure to the base plate.
9. Screw the inlet air inlet louvre to the enclosure, hang the panel (exhaust louvre) in the enclo‐

sure and secure it with the snap fasteners.

6.10.2.4 EPC 1100–G / EPC 1500–G

Material Supplied additional components for air filter

Modifying the air filter

Fig. 26 Modifying the air filter, EPC 1100–G / EPC 1500–G

Air filter

EPC 1100-G

EPC 1500-G

Angle

EPC 1100-G

EPC 1500-G

Before modification

After modification

1. Unscrew the air filter from the cylinder head and clean, if necessary.
2. Screw the elbow into the cylinder head and then the air filter to the elbow.

Further information See chapter 10.4 for information on air filter maintenance.

Fitting the sound enclosure

Precondition The air filters are modified,

the rubber pads are removed.

Installation

6.10 Retrofitting the sound enclosure (accessory)

Assembly and operating manual 1-stage piston compressor
EPC-G

No.: 9_5752 24 E

Summary of Contents for EPC 1500-G







































































































Search results

Summary of Contents for EPC 1500-G

Reviews:

Related manuals for EPC 1500-G

Brands by name

Popular brands

KAESER EPC 1500-G, Assembly And Operating Manual

Search results

Summary of Contents for EPC 1500-G

Reviews:

Related manuals for EPC 1500-G

Brands by name

Popular brands