manualshive.com logo in svg

Jung ZLLA5004M, Operating Instructions Manual

Share
Download
Jung ZLLA5004M Operating Instructions Manual Download Page 15

Figure 21

o

Press the 

Ƌ

 and 

ƍ

 buttons simultaneously until the LEDs flash green.

After 10 seconds the LEDs flash green quickly: The transmitter searches for an update.
The LEDs flash red: Update in process.
The LEDs flash green for 3 seconds: Update successful.
The LEDs flash red quickly for 10 seconds: Update not successful.

i

In order to cancel the update, press any button.

7 Mounting

Precondition: To ensure good transmission quality, keep a sufficient distance from any possible
sources of interference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts
or transformers. 

i

Perform commissioning procedures before installation (see chapter Commissioning).

Figure 22

o

Change the battery (see chapter Changing the battery).

o

Screw or glue the base plate (5) to an even surface. The 

TOP/OBEN

 label has to be at the

top.

o

Position the design frame (7) on the base plate.

15/17

32596203
J0082596203

23.05.2016

ZigBee radio transmitter module 4-gang

Summary of Contents for ZLLA5004M


















Reviews:

No comments

Brands by name

Popular brands

Load more brands